Ver el contenido principal
Soluciones Moen

Llave de cocina 3 en 1 Filtración de agua: fuga debajo de la base del fregadero

  1. Última actualización
  2. Guardar como PDF
24/7 Leak:

If the 3-in-1 Water Filtration Pulldown Kitchen Faucet is leaking under the sink 24 hours a day, use Figure 1 below to check the home shut off valves/angle stops (#1), las líneas de suministro de la casa ( #2) que conducen a la llave y a las tuberías de suministro de la llave Moen ( #3). Cuando la fuga proviene de las tuberías de suministro de la casa o de las válvulas de cierre de la casa ( #1 o 2), deberá comprarlos en su tienda local para el hogar. Si la llave tiene pérdidas de las líneas de suministro de la llave Moen ( #3), contáctenos llamando al 1-800-BUY-MOEN (1-800-289-6636).

Intermittent Leak:

If the 3-in-1 Water Filtration Pulldown Kitchen Faucet is only leaking under the sink after the faucet has been used, the issue would be from another of the under deck hoses/lines (Figure 2 and 3) .  Esta llave está combinada con un sistema de filtración de Moen (filtración avanzada F9800 u ósmosis inversa F9900); consulte la Figura 3 para ver un diagrama detallado de la configuración bajo cubierta. If you have the 3-in-1 Water Filtration Pulldown Kitchen Faucet  paired with a F9900 Reverse Osmosis system installed, please see below for solution of a leak coming from the RO filter. For leaks from other hoses/lines or models contact us by calling 1-800-BUY-MOEN (1-800-289-6636).

Figura 1

1111111111111111111

Snag_c2c709.png

Figura 2-Líneas de la llave

(Las configuraciones varían según la instalación).

Snag_1244019.png

Figura 3-Ejemplo de instalación de ósmosis inversa

(Las configuraciones varían según el modelo,)

Snag_3b7b3b.png

 
3-in-1 Water Filtration Pulldown Kitchen Faucet and F9900 Reverse Osmosis Installations:

Consumers who suspect a leak beneath the filter canister of the RO Filter (D) should first verify the correct assembly of the Flow Restrictor within the RO Filter (D). This crucial step in the installation process, performed after attaching the filters, is essential for preventing leaks in this area. 

The RO Filter can be identified by the Elbow projecting from its base. The Flow Restrictor is situated inside the 1/4" tube connected to this Elbow.
Before proceeding with troubleshooting, it is advisable to confirm whether this is indeed the source of the leak. To do this, wrap a towel or rag around the base of the RO filter and turn on the faucet. If the towel becomes wet, this indicates that the leak is originating from this area, and you can then proceed with the troubleshooting steps.

How to verify you have installed the Flow Restrictor in your F9900 Reverse Osmosis System:
clipboard_e1e33a5d175cb5e8aa2e5f7f9f18395a0.png
  1. Manifold
  2. Sediment Filter
  3. Pre-Carbon Filter
  4. RO Filter: Includes Flow Restrictor
  5. Post-Carbon Filter
  6. Manifold Screw (x2) 
  7. Tank Elbow
  8. Cold Water Tee
  9. 1/4’’ Black Inlet Tube
  10. 1/4’’ Blue Air Gap Tube
  11. 3/8’’ Blue Air Gap Tube
  12. 3/8’’ White Tank Tube
  13. 3/8’’ Gray Outlet Tube
  14. Sealant Tape 
  15. Screws and Nuts, Drain Saddle (x2)
  16. Foam Seal
  17. Drain Saddle
  18. Tank
  19. Dropper
  20. Large Elbows (x2)
  21. Small Elbow
  1. Ensure that the water supply shut-off valves are turned off. For detailed instructions, refer to the article How to Turn Off the Water Supply to the Faucet.
  2. Place a bucket, pan, or rag under the filtration system to catch any residual water.

2026-01-26_11-32-42.PNG

 

  1. To release the 1/4" tube, gently depress the Elbow Retaining Ring (3) while pulling the 1/4" tube (J) out of the Elbow (4).

clipboard_e172e6a6469631780b499534b61f15d4c.png

  1. After removing the 1/4" tube (J) , examine the opening at the end.
    • dosificador de flujo (2) Installed:
      • The Flow Restrictor (2) should be visibly protruding from the end of the 1/4" tube (J) .
      • Ensure that the red collar of the Flow Restrictor (2) is seated against the tube, leaving 1/8" of the thin, clear tubing exposed.
    • dosificador de flujo (2) Not Installed:
      • If the 1/4" tube (J) is hollow, the Flow Restrictor (2) was not installed, which may be causing a leak from this area.
      • The Flow Restrictor (2) is coiled and packaged between the top of the RO Filter (D) assembly and the Protective Cap.
      • Please reference the installation guide INS12980A...Step 14.
  2. If you continue to experience a leak from this area or any other hoses, please contact us by calling 1-800-BUY-MOEN (1-800-289-6636).

Para obtener información adicional sobre los productos Moen, visite solutions.moen.com y seleccione el tipo de producto que está reparando. La guía incluirá detalles sobre la reparación, resolución de problemas e información específica sobre cómo ensamblar manerales asociados con ese estilo de producto.  

¿Sigue sin encontrar lo que busca?

Contáctenos o llame al 1-800-BUY-MOEN           

¿No está en los EE. UU.?  Moen Canadá | Otros Sitios internacionales